GPS magnetic portable locator GTA5B ultra long standbyGPS terminal product specification

One, product introduction

Long standby tracker is a battery powered only by theterminal communication, positioning, day to upload a point(set), the standby power consumption is very low. No need for wiring installation, portable. Comes with two magnetic.Drip proof dustproof design. Environment dependent 2~3 years.

1, product overview

Product Name: ultra long standby vehicle positioning terminal

Product type: GTA5B

Product specifications: L81mm*W58mm*H28mm

Two, the parameters and functions of the operating instructions

1, the product machine parameter table

Serial number

Project

Specifications and parameters

Note

1

Working voltage

DC2.4V~3.6V

2

The working current

60~80mA@3V

3

Standby current

Less than 3uA

4

Size specifications

L81mm*W58mm*H28mm

5

Positioning method

GPS positioning module and a combination of base station positioning

6

The positioning error

<10m (this data is only for reference, and the vehiclepositioning error

Are related in the regional topography and time etc.)

This data to the company laboratory measurement

7

Communication network

GPRS

8

Communication mode

UDP

9

Operating temperature range

-25 C ~ +75 C

10

Storage temperature range

-40 C ~ +85 C

11

Net weight

120g

12

Battery operating time

Continuous work for 2~3 years (about the visual environment and parameters)

The 2 section Panasonic battery

1500MA*2

2, product function table

Serial number

Functional specifications

Function description

1

Timing position feedback

In the wake of a specific point in time of day, return the location data immediately after the dormancy

2

Support for /GPS base station location

Automatically enabled when GPS cannot locate the base station positioning under the condition of

3

Free installation and wiring

Does not require any external circuitry, with strong magnetism

3, the data send instructions:

Install batteries set parameters after each time point towake up, first open the GPS power supply terminal, 3 minutes, if the location within 3 minutes, immediately shut down the GPS module power supply, record the final state of longitude, etc.. If no positioning the most open for 5 minutes. 5 minutes without positioning using LBSpositioning model. Upload to server data, location datauploaded by the terminal needs to GPS and the base station location information and the battery voltage information to the server

New features, GTA5B 4

1 supports up to 4 time wakeup time (4 arbitrary time point)

2 supports message configuration on-line parameters andwake up time

3.APN maximum 16 characters, the machine number of a maximum of 16 characters

4 support the school function

5 increase the electric quantity display function (the defaultterminal can transmit 1000 GPRS data, if it has sent 500, isfor 50% of electricity consumption,

Extended instruction 0x00 0x08 upload)

6 increase the time return mode setting unit for minute(permission to set the interval for 0-300 minutes, 0 offtiming return, timing interval greater than or equal to enable hibernation feature 30 minutes)

5, the on-line setting

On-line step:

Disassemble a SIM card - fitted with two batteries - with a special data line connecting terminal and computer - open the computer, parameter setting software - good parameter settings - set OK pull out line screw on the shell - suction to complete the installation of the car -

Parameter setting software: (this software generally used for mass production equipment when setting software, the software function and SMS transmission method has the same effect. Ordinary customers to use the method of SMSsettings parameters can be.)

A. select the corresponding serial port, baud rate to 9600,open the serial port

B. settings need to be IP and port settings

C. setup requires APN

D. set the machine number (terminal to check the numberto upload data)

E. set wake-up time every day

The F. can carry out school of terminal (Note: the time of the terminal when the power is not saved)

Good G. input parameters to be set, click the "Settings" button, after successful setting will prompt set successfully,whereas the prompt set failure

The matters needing attention:

1, a good set of parameters, settings will immediately send a data to the platform, also can pass by wake button triggersending circuit board (press).

2, the terminal installation and the battery indicator light will light up, light corresponding communication module, the yellow light corresponding to GPS module.

6, the indicator light:

Indicating lamp type

Indicator lamp status

GSM lamp (red)

Often death: communication is abnormal or light damage

Chang Liang: say no signal or registered on GPRS network

Slow flash (1 times / sec): GPRS signal, but not on the line

Flash (2 times / sec): terminal in a normal line

GPS lamp (yellow)

Often death: positioning module is damaged or enter a sleep mode

Chang Liang: terminal work abnormally

Slow flash (1 times / sec): terminal to find the satellite signal, but not effective positioning

Flash (2 times / sec): terminal effective positioning

Three, after-sales service

1 of the products from the date of installation, enjoy one year warranty. The warranty period is non-human factors or product quality caused by design

Damage to the equipment, please contact or call the company after-sales service department to deal with.

2 of the customers who dismantled or force majeure (such as flood, vehicle accident damage not repair).